X axis travel:   3100mm

Z axis travel:   240mm

Diamond blade diameter:      400mm

Blade bore size:          50mm

Profiling wheels:         Bore size 35mm – lower diameter 60mm

Main motor power / rotation speed: 5.5 kW = 7.5HP – 1400 rpm (1700 rpm 60Hz)7.5 kW = 10HP – 2800 rpm (3400 rpm 60 Hz)

Standard voltage-frequency:  400V-50Hz / 230V-60Hz

MULTISYSTEM

MAIN MOTOR: 3-phase 4/2 poles 400V 50Hz 1400/2800rpm - Power 5.5/7.5KW (7.5/10HP)

CUTTING, profiling OPT193, edge polishing OPT194 and chamfering OPT195 machine.

MACHINE STRUCTURE

Sturdy and compact steel frame, sandblasted and ceramic coated. E-chains to protect and guide moving cables.

WORKTABLE

- Work table fabricated in galvanized steel rails

- Dimensions of the worktable: 3960 x 900 mm

HEAD

- Head motion on angled rack and pinion.

- Motorized head feed with variable speed from 0 to 7 m/min both

both forward and reverse. Head travel: 3100 mm

- Selection of three different head feed modes:

  Mode "0": forward and no reverse

  Mode "1": forward and reverse continuously

  Mode "2": forward and reverse, one cycle only

- Motorized working depth adjustment with variable speed from 0 to 0.6 m/min. Travel: 250mm

MOTORS

- Power supply: 400V 50-60Hz three phase (different voltages on special orders)

- 2-speed main motor

  Low speed for granite, power 5.5KW=7.5HP - 1400rpm at 50Hz   High speed for marble, power 7.5KW=10HP - 2800rpm at 50Hz

CONTROLS - MAIN ELECTRICAL PANEL:

- Main isolator switch

- 2-position speed selector for main motor

- Water pump switch

- Emergency stop push button

- Power-on “RESET” button

CONTROLS - MOBILE CONTROL PANEL:

  Main motor start/stop button

  Head forward and reverse buttons on the X-axis

  Head forward and reverse variable speed controls   Main motor raise and lower buttons on the Z-axis   Blade raise and lower variable speed control

  Pop-up rollers raise and lower button

  3-mode head feed selector

  Emergency stop push button

  Digital Ammeter

TOOLS (not included)

- Diamond blade Ø 400 mm, 50mm bore.

SAFETY

- Motor overload protection device.

- CE standards compliance.

MEASUREMENTS AND WEIGHT

- Total length: 4288 mm

- Total width (without side table): 1200 mm

- Total height: 2220 mm

- Net weight (without accessories): 953 Kg

- Weight (with accessories): 1225 Kg

OPTIONAL

MAS - PROFILING KIT

Head tilt from 90° to 0° for working the edge of slabs up to 60 mm in thickness

Main motor slide for working of slab edge

Tools technical features:

Diamond profiling and edge polishing wheels with 60mm lower diameter (bore 7/8') or 150mm (bore 35-30-22,2mm) for marble and granite slabs up to 60 mm in thickness.

MAS - CHAMFERING KIT

Head tilt from 90° to 0° for working the edge of slabs up to 60 mm in thickness Main motor slide for working of slab edge

Tools technical features:

Wheels 130mm diameter with left handed snail lock.

MAS - FLAT EDGE POLISHING KIT

Head tilt from 90° to 0° for working the edge of slabs up to 60 mm in thickness Main motor slide for working of slab edge

Tools technical features:

Wheels 130mm diameter with left handed snail lock.

LASER ALIGNMENT DEVICE

To achieve an effective cutting optimization, a laser diode mounted on the head shows the blade's cutting line. In this way, the guiding beam is oriented according to the head rotation.

Laser beam in red color

Power 20 mW

HYDRAULIC POP-UP ROLLERS (MOTORIZED)

To facilitate slab loading and positioning:

- Roller table with 32 omni-directional rollers

- Pop-up rollers raise and lower by motorized hydraulic system

WATER TANK & BUILT-IN RECYCLING PUMP

- Steel tank, capacity 550 liters approx.

- Water pump: 0.5Kw motor - max capacity 250 l/min.

SIDE EXTENSION TABLE (without